1 1Operator’s Manual10 in. COMPOUND MITER SAW WITH LASER TRAC®Model No. 137.212360CAUTION:Before using this Miter Saw,read this manual and followall
10 1110 11KNOW YOUR COMPOUND MITER SAWCover Plate Lower Blade Guard Hold-down ClampBaseUpper Plate GuardMiter Lock HandlePositive Stop Locking LeverDu
10 1110 11GLOSSARY OF TERMSCOMPOUND MITER SAW TERMSARBOR LOCK – Allows the user to keep the blade from rotating while tightening or loosening the a
12 1312 13ASSEMBLY AND ADJUSTMENTSINSTALLING THE MITER HANDLE (FIG. A)1. Thread the miter handle (1) into the hole (2) located at the front of the mi
12 1312 13REMOVING OR INSTALLING THE BLADEOnly use a 10-inch diameter blade.To avoid injury from an accidental start, make sure the switch is in the O
14 1514 15Installing Blade (Fig. G, H, I)1. Install a 10 in. blade with a 5/8 in. arbor making sure the rotation arrow on the blade matches the cloc
14 1514 155. If the miter angle desired is not one of the nine positive stops, simply lock the miter table into position by turning the miter handle
16 1716 1790° Bevel Indicator (Fig. N)1. When the blade is exactly 90° to the table, loosen the bevel indicator screw (5) using a #2 Phillips screwd
16 1716 17NOTE: Mounting hardware is not included with this tool. Bolts, nuts, washers, and screws must be purchased separately.2. For portable use,
18 1918 19OPERATIONSAFETY INSTRUCTIONS FOR BASIC SAW OPERATIONBEFORE USING THE MITER SAWTo avoid mistakes that could cause serious, permanent injury,
18 1918 19PLAN YOUR WORK● Use the right tool. Don’t force a tool or attachment to do a job it was not designed to do. Use a different tool for any wo
2 32 3TABLE OF CONTENTSSECTION PAGE SECTION PAGEWarranty ... 2 Know Your Compound Miter Saw ... 10P
20 2120 21TURNING SAW ON (FIG. T)To reduce the likelihood of accidental starting, a thumb activated lock-OFF switch is located on top of the switch ha
20 2120 21123COMPOUND CUT (FIG. W)A compound cut is the combination of a miter and a bevel cut simultaneously.1. Loosen the bevel lock handle (1) and
22 2322 23Fig. Z Bevel/Miter SettingsFig. AASettings for standard crown molding lying flat on compound miter saw tableMiter Saw TableFenceILIROLORO
22 2322 23MAINTENANCEMAINTENANCETo avoid injury, never put lubricants on the blade while it is spinning.To avoid fire or toxic reaction, never use gaso
24 2524 25TROUBLESHOOTING GUIDETo avoid injury from accidental starting, always turn switch OFF and unplug the tool before moving, replacing th
24 2524 2510 in. COMPOUND MITER SAW MODEL NO. 137.212360 When servicing use only CRAFTSMAN replacement parts. Use
26 2726 2710 in. COMPOUND MITER SAW MODEL NO. 137.212360SCHEMATIC FOR SAWX3PJX3RQX3S6X3SGX3SHX3SJX3SFX3STX3SMX3S8X
26 2726 2710 in. COMPOUND MITER SAW MODEL NO. 137.212360PARTS LIST AND SCHEMATIC FOR MOTOR
28 2928 29REPAIR PROTECTION AGREEMENTS Congratulations on making a smart purchase. Your new Craftsman® product is designed and manufactured for years
28 2928 29® Registered Trademark / TM Trademark / SM Service Mark of Sears Brands, LLC® Marca Registrada / TM Marca de Fábrica / SM Marca de Servicio
2 32 3WARNING ICONSYour power tool and its Operator’s Manual may contain “WARNING ICONS” (a picture symbol intended to alert you to, and/or instruct y
4 54 5POWER TOOL SAFETYGENERAL SAFETY INSTRUCTIONSBEFORE USING THIS POWER TOOLSafety is a combination of common sense, staying alert and knowing how t
4 54 5POWER TOOL SAFETYto determine that it will operate properly and perform its intended function – check for alignment of moving parts, binding of
6 76 7COMPOUND MITER SAW SAFETYSPECIFIC SAFETY INSTRUCTIONS FOR THIS COMPOUND MITER SAW1. DO NOT USE THIN KERF BLADES they can deflect and contact gua
6 76 7ELECTRICAL REQUIREMENTS AND SAFETYGROUNDING INSTRUCTIONSIN THE EVENT OF A MALFUNCTION OR BREAKDOWN, grounding provides a path of least resistanc
8 98 9ACCESSORIES AND ATTACHMENTS TOOLS NEEDED FOR ASSEMBLYRECOMMENDED ACCESSORIES● Use only accessories recommended for this miter saw. Follow inst
8 98 9CARTON CONTENTSUNPACKING YOUR MITER SAWTo avoid injury from unexpected starting or electrical shock, do not plug the power cord into a source of
Komentarze do niniejszej Instrukcji